Pinards PDF

Owner’s Manuals. Below, you may find manuals for your Beretta firearm in an electronic format. You may also order a hard copy if desired. Owner’s Manuals. Unofficial Beretta Site: really neat site, complete with the history of the model 92 series, old ‘owner’s manual, exploded views, 70 (Thanks to Ed Ruesing, he gave me the opportunity to post the manual) KB, English AL ( KB). The illustrations and instructions in this article are based on the Beretta Urika , but they are also valid for the other versions of the

Author: Tale Voodootaur
Country: Libya
Language: English (Spanish)
Genre: Sex
Published (Last): 8 November 2016
Pages: 328
PDF File Size: 17.45 Mb
ePub File Size: 17.63 Mb
ISBN: 401-6-47271-859-4
Downloads: 73852
Price: Free* [*Free Regsitration Required]
Uploader: Douzil

If you miss your target or if the bullet penetrates the tar- get, it is your responsibility to ensure that the shot does not cause unintended injury or damage.

That is one of the reasons you should make sure the gun urikka cocked and put the safety on before you start to remove either the bolt or the trigger group.

All ‘s sold in the US as far as I know come with a plug installed to limit shell capacity to 1 in the chamber and 2 in the magazine, with a longer plug in the box to limit capacity to 1 and 1.

I do that, but I do not recommend it for a gun that will be used for any purpose other than clay shooting. Sometimes the bolt will seem to go in OK but it won’t slide back all the way.

They will go at least 10 times as long between cleanings with clean ammo like Rio than with dirty ammo like Federal Top Gun. The bore and cartridge chamber must be clean and free from ob- structions. Lower the hammer on the unloaded gun by pulling the trigger. It is common for clay shooters to remove the safeties from guns that are dedicated to clay shooting only. Do not store firearms in places which are or could be accessible by children or other persons whose unfamiliarity with firearms might lead to unsafe use.

For best results with steel shot, Beretta recommends a modified choke.

I have found that a magnet shaped like a pencil helps a lot in putting the rear plate and lock washer in place while the gun is held vertical, butt up. Use the two hook wrenches together as illustrated to break the counter nut loose. I Receiver-stock spacer made of technopolymer, fiber-glass reinforced. Most Excellent Mr Ben For lack of a better name, I’ll call them valve ports. Next remove the valve nut and the valve, valve centering ring, and valve spring parts, and respectively.

  JERZY HOLZER DEMOGRAFIA PDF

I am also aware that I am a lousy photographer, but you and I will both just have to live with that! Do not oil these parts. If the deposits are soft, a pipe cleaner may be enough, but I have seen some deposits that were much harder – it depends on the ammo you use. After it has been out a few times, the trigger group will loosen up and it will go in and out easily.

Mon Feb 26, 2: If you want to do a complete disassembly, I would suggest doing it in the following order: Use the screwdriver to center the plate and the washer. The fore- end is correctly assembled when there is no space left between the parts. However, if you let the nut get real dirty before you try to clean it you may never be able to get the ring, metal washer and plastic bushing out.

With the retaining pin out, the firing pin and spring just slide right out. Never handle a loaded firearm until you are fully familiar with the loading procedures.

Beretta Web – Owner’s Manuals

Feeding from magazine is blocked. Mon Feb 26, The magazine tube cap Part 45, including the shaft that the piston and forend nut fit on screws into the end of the magazine tube part For instructions on how to reinstall the carrier, see section F below in “Reassembly of the trigger group”. Most people use a small propane torch, but if you don’t have one you can do it by sticking the cap through the cracked-open door of a kitchen oven preheated to around deg.

The spring and veretta tube may need cleaning once in a while if you are using very dirty ammo that leaves a lot of ash. Removing the stock, and using stock shims: They can be turned different ways to produce cast off marked DX or cast on marked SX and any of several amounts of drop marked in millimeters.

It is possible to increase the magazine capacity from two to three rounds in the coun- tries where it is allowed. Before starting the disassembly of the exhaust valve assembly, carefully observe the position ak391 the components parts. Make sure that the spacer shows on the top the drop and cast wanted “CDX” in the drawing.

  AXEL CLEEREMANS PDF

Removing the bolt assembly: The stock drop and cast of the spacer c must always correspond to those of the metal plate j. If necessary, a screwdriver can be used in the end of the cap shaft.

The pin is held in position by spring pressure as long as the button is out, manuap it will get loose if: Other models of Beretta gas-operated shotguns which have the recoil spring in the stock are very similar and the pictures and instructions here may be helpful, keeping in mind that there are some variations. They are hard to use because the counter nut is put on manuzl tight at the factory, and the valve nut has a long threaded portion, requiring that it be turned a lot with the wrench.

Now manuzl the whole works down into the receiver.

You can remove the trigger group with the bolt in or out, but it is easier to get the bolt back berretta if the trigger group is already out. Tue Jun 19, 2: A weak spring will allow the bolt to come back too fast when the shot is fired, which over along time period can result in damage to the bolt and the receiver.

Very nice Mr Ben! The focus of this article is disassembly and reassembly, not cleaning and maintenance, although I make a few comments on those issues.

Beretta AL391 Teknys Gold Target Owner Manual (Spanish)

When I did the cleaning with a thinner wire I had trouble with failures to eject, breetta the ports were open to some extent, but too narrow.

Always check the barrel prior to loading to ensure that it is clean and free from obstructions. To reverse the safety for a left-hander, just turn the button end-for-end and put it back in. Full choke constriction when using steel shot does not increase pattern density and often distorts normal pattern density associated with lead.

Thu Apr 05, 4: It mwnual be engaged when the breech bolt is positioned in the closed position with the use of one hand.