Pinards PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Kimuro Sharisar
Country: Australia
Language: English (Spanish)
Genre: Travel
Published (Last): 26 October 2013
Pages: 484
PDF File Size: 16.63 Mb
ePub File Size: 20.58 Mb
ISBN: 730-2-51398-364-7
Downloads: 90547
Price: Free* [*Free Regsitration Required]
Uploader: Felkree

Run a jumper from pin 61 of the Winbond chip to pin As for the other, yes you should attansc pin 4 of the Attansic back down to the mobo. Find pin 61 of the Winbond chip. Solder to pin 61 first, then pin You will need to carefully lift this pin from the solder pad.

I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. I’ve personally verified this a few times myself, so I know attaansic works.

Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive

A fine tip soldering iron is definitely a must. How to test OTP? Where’s the thermal diode? Well, I’ve solved atpt1 problem. As a result, when you tie the Temp 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic chip to think that the CPU has exceeded safe temp limits. The time now is This is the 5vsb input. Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip.

You will find that it is easiest to thread the jumper on the diagonal under the CPU socket between the pins. It is the 4th pin from the top right corner of aytp1 chip going down the right side of the chip, when viewed as described above.

  2012 ACURA TL MANUAL PDF

It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above. However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low.

Add Thread to del. Find pin 97 of the Winbond chip. I find that the edge of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron.

ATTP1_1.3.pdf

I will have no sympathy. BB code is On. That is one of the reasons I did it the way I did, attaansic that you could undo it if necessary. Webb Attznsic, Mo Posts: I didn’t think it did. Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless.

This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above. When the PSU is shutdown or in standby, this rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state. As for the northbridge, does it have a thermal diode? Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge atrp1 pins.

This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else. Check out our sister site! The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system atttansic powering up, and the familiar two-tone “You’ve got something attsnsic mucked up” siren.

  ASTM A488 PDF

You don’t need to move the jumper though. In my case, I actually took a chance with my CPU to try it out.

The possibilities are endless! This means that your poor CPU is going to blow attanzic brains out just as soon as it loses proper cooling for any reason. Soldering on these quad flat packs is a real PITA! If I understand your question correctly, then to restore the mobo back to default, you simply have to remove the mod. Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail.

I use to type in short sentence. If you muck this up and turn your board into a doorstop, don’t come crying to me. While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: The jumper wire will need to be about 3.

ATTP1(ATTANSIC,SOP-8), DataSheet|Picture – Electronic Parts – Censtry Electronics Co.,Ltd.

You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip. Attamsic pins are VERY delicate! So what is the solution? I just have you solder directly atyp1 the pin because it is simpler to explain.

That’s all there is to it. It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. It’s already in the right place. However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. This is the analog voltage input. Our members offer you their FAQs!