Pinards PDF

This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D20 on. ASTM D is a testing standard designed to measure the friction of plastic film and sheeting. The ASTM D standard test method is used to determine the kinetic (moving) and static (starting) resistance of one surface being dragged.

Author: Dorisar Grokora
Country: Lebanon
Language: English (Spanish)
Genre: Politics
Published (Last): 28 August 2013
Pages: 108
PDF File Size: 17.32 Mb
ePub File Size: 3.31 Mb
ISBN: 342-8-21816-736-4
Downloads: 26897
Price: Free* [*Free Regsitration Required]
Uploader: Shaktiran

Auditing Consulting Sourcing Training. Both procedures yield the same coefficients of friction values for a given sample. For this reason, it is sometimes meaningless to compare slip and friction properties of adtm or sheets produced at different times, unless it is desired to study this effect. The kinetic coefficient of friction is equal to the average force reading obtained during uniform sliding of the surfaces divided by the sled weight.

These methods yield empirical data for control purposes in film production. Both static and kinetic coefficient of friction can be calculated.

Contact Us View Accessories Catalog. Where products have been made by different processes, or even on different machines by the same process, their surfaces may be dependent on the equipment or its running conditions.

It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements. They are designed with standard and optional asrm that increase testing efficiency and improve the testing experience for the operator.


Subscribe to Our Newsletters. Historical Version s – view previous versions of standard Translated Version s: Certification Formally confirming that your products and services meet all trusted external and internal standards.

Coefficient of Friction ASTM D

The force to get the sled started static and to maintain motion kinetic is measured. Therefore, it is advisable to refer to that material specification before using this test method.

Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Because this blooming action may not always be uniform on all areas of the film surface, values from these tests may be limited in reproducibility. Standards can be obtained from appropriate standards authorities. Low force measurement Data rate used to capture peaks and troughs Reporting calculations in compliance with the standard Instron’s Solution: We use cookies to improve your browsing experience.

Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world.

ASTM D1894-14 Coefficient of Friction of Plastic Film

For a specific precautionary statement, see the end of 6. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Glossary of Materials Testing Terms. The film under test is secured on a flat surface and a sled of known weight is wrapped in the same material.

Coefficient of Friction ASTM D1894

Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. These additives have varying degrees of compatibility with the film matrix. The coefficients of friction are related to the slip properties of plastic films that are of wide interest in packaging applications. Care should be exercised to ensure that the rate of motion of the equipment is as carefully controlled as possible.


Correlation of test results with actual performance can usually be established. Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes.

Inspection Validating the specifications, value and safety of your raw materials, products and assets. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Validating the specifications, value and safety of your raw materials, products and assets. Global Reach Intertek is the industry leader with over 42, people in d1984, locations in over countries. Some of them bloom, or exude to the surface, lubricating it and making it more slippery.