Pinards PDF

DESCRIPTION. The LM and the LM are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power. CC Datasheet, CC PDF, UPCC. Part Number, CC. Manufacturer, NEC. Short Description, UPCC. Long Description, www. CC UPCC Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated circuits (ic).

Author: Dubar Nebei
Country: Rwanda
Language: English (Spanish)
Genre: Art
Published (Last): 22 October 2004
Pages: 497
PDF File Size: 18.60 Mb
ePub File Size: 16.70 Mb
ISBN: 302-4-82127-754-7
Downloads: 38976
Price: Free* [*Free Regsitration Required]
Uploader: Gogal

Could this finally be the dawn of room-temperature superconductors? Just so that I am clear. As for the power supply, the opamp is actually being operated as an opamp rather than a comparator.

(PDF) C1458C Datasheet download

Spinaker, You will notice that I have merged the newer post with the older post since the second thread was a continuation of the first. Motion-Activated Trail Camera In this Teardown Tuesday, we are going to take a look at the inner workings of a trail camera! Nov 13, 6. What dahasheet do you measure across capactors C and C?

This will help prevent confusion since replying members will be less likely to be confused. Posted by Gamedojo in forum: Here are my voltage readings for the -8 section.

Can I use a LMCN or TL opamp in place of a CC? | All About Circuits

Can we use a tristate buffer in place of voltage level shifter? Do you already have an account? In the meantime, I will use the values you have measured. A Non-Invasive Glucose Sensor Researchers believe that sweaty armpits may be the answer to both detecting and controlling diabetes.

  GN9350 MANUAL PDF

I can’t seem to find a datasheet for a CC, but the pinouts on the schematic agree with the above opamps. Your name or email address: Would one of these work for now? With an increase in the base drive applied to Q, it begins to turn on harder.

Nov 13, 9. The trick to the -8volt regulator stage is that Q is acting to control the positive-most end of the 15V secondary transformer winding so that it is exactly 7 volts positive when measured with respect to ground.

C1458C Datasheet PDF – NEC

Nov 13, 3. I have included the PS schematic below. This results in a restoration of the -8volt output so that the droop due to the increased load is cancelled. I started reviewing the vatasheet on op amps on this site because I think the problem with my Tek scope power supply is a bad op amp. Nov 13, 8. Quote of the day. This action pulls the positive end of the transformer secondary supplying the 15V DC down slightly.

This causes the output of the opamp to go positive which drives the base of transistor Q which in c1458v drives the base of Q positive.

I have it working. Nov 13, Nov 13, 7. Nov 13, 5. First off it was probably not necessary to start a new thread since members are going to be a bit confused between the two.

  LAS HORMIGAS BERNARD WERBER PDF

I really do not care if one of these is the best choice. Nov 13, 1. Is this a good enough test for U A and B in t his schematic? You May Also Like: Yes, my password is: Posted by spidermanIIII in forum: You placed your DVM probes on the negative and positive terminals of the capacitor and the voltages you posted are the ones you read. Oct 29, 7, 3, If the opamp is in a socket, why not try testing it on the bench? Jan 28, 9, Jul 17, 22, 1, Discussion in ‘ General Electronics Chat ‘ started by spinnakerNov 13, I went out a purchased a couple of op amps from Radio Shack and built a comparator like the first one on this page.

Actually the voltage measurement I would like you to make is the voltage across the terminals of the capacitor. That is because in both cases the ground reference is not a direct connection to ground. Can U use 2 transistors in place of a relay to switch 2 different voltages Posted by icadj in forum: Bottom line, compare the datasheets of the op amps for compatability.

If you imagine that the load on the -8V output increases then the -8volt output would drop slightly toward 0v.