Pinards PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Meztigami Galrajas
Country: Algeria
Language: English (Spanish)
Genre: Sex
Published (Last): 13 November 2018
Pages: 81
PDF File Size: 4.90 Mb
ePub File Size: 8.48 Mb
ISBN: 420-6-73668-240-6
Downloads: 55567
Price: Free* [*Free Regsitration Required]
Uploader: Mooguzshura

ASTM F 146 – 04

The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a asym test when agreed upon between the purchaser and the manufacturer. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D A number in parentheses indicates the year of last reapproval.

Change the distilled water used in the test frequently. Pour enough fresh fluid into the tube to completely cover the specimens and ensure that they are immersed.

It is understood that the results will be reported per D along with the specific immersion conditions used prior to said adhesion test. The change in weight of the specimens is to be calculated as an expression of percentage change on the original weight.

ASTM F146 – 12

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. The inch-pound units in parentheses are for information only.

Significance and Use 4. There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and thickness change atsm IRM oil. Use enough fluid to provide a minimum of 10 mL for each specimen in the container. Temperature of Test Measurement 7. Use the same sinker throughout.

  HAYNES SHOCKLEY EXPERIMENT PDF

Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven. Please copy and paste this embed script to where you want f1446 embed Embed Script. The specific test fluids and test conditions outlined were asm as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

Summary of Test Methods 3.

These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D This gives the final volume, V2. Measure the weight of the test specimen to the nearest 1 mg 0.

We are a non-profit group that run this website to share documents. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce. We need your help!

ASTM F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials

F — 04 Standard Test Methods f1446 Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Please fill this form, we will try to respond as soon as possible. We need your help to maintenance this website. If such information is not available, then the material should be tested by itself in fresh fluid to determine compatibility with said fluid. ICS Number Code Originally approved in Thank you for interesting in our services. NOTE 1—Coolant mixtures are typically tested under boiling reflux conditions.

  1970 CORVETTE MANUAL PDF

NOTE 2—Great care must be asgm to record the swollen thickness when the needle slows to a different rate which reflects indentation into the softened specimen. After immersing the specimens in the various test fluids, the effect on physical properties is expressed as change in tensile strength, compressibility in softened condition, flexibility, volume change, and thickness and weight changes from the original condition. This standard has been approved for use by agencies of the Department of Defense.

The change in thickness of atsm specimens is to be calculated as an expression of percentage change from the original thickness. The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce.

Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by v146 fluid. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM F – 12 Standard Test Methods for Fluid Resistance of Gasket Materials

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Please help us to share our service with your friends. The user should be aware that results may differ.