Pinards PDF

Flat Glass Inspection Criteria per ASTM C – 11/ASTM C Terminology. crush:lightly pitted condition with a dull gray appearance. dig:deep, short. Find the most up-to-date version of ASTM C at Engineering This standard is issued under the fixed designation C ; the number ASTM Standards: 2 cut size, n—glass ordered cut to its final intended size.

Author: Tesida Mazutilar
Country: Angola
Language: English (Spanish)
Genre: Business
Published (Last): 7 January 2013
Pages: 402
PDF File Size: 17.77 Mb
ePub File Size: 4.18 Mb
ISBN: 925-9-56228-716-3
Downloads: 9490
Price: Free* [*Free Regsitration Required]
Uploader: Kajijas

Opening in the mesh shall not exceed 32 mm 11? Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material.

It is informational only and not an official part of the standard; the full text of the standard c136 must be referred to for its use and application. The allowable blemish sizes listed in Table 9 do not include associated distortion.

Flat Glass Inspection Criteria per ASTM C – 11/ASTM C | Consolidated Glass Corp

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Allowable blemishes per Table 3 PLUS three rejectable point blemishes Production of architectural glass products including coated, heat treated, laminated, and other select glass products. The values given in parentheses are for information only.

Provides guidelines for categorizing and qualifying unintended visual obstructions in an IGU. Type I which is c10336 transparent flat glass and Type II which is a patterned and wired flat glass. F Allowed with a minimum separation of mm 48 in. Production of architectural glass products including coated, heat treated, laminated, and other select glass products.

The lower of the two interference angles measured shall be used to compare to the evaluation criteria in Table 6. This specification covers the quality requirements of flat, transparent, clear, and tinted glass intended to be used primarily for architectural glazing products.

  DIGITAL TEXTURING AND PAINTING OWEN DEMERS PDF

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Point blemish, linear blemish content, associated distortion, dimension, squareness, reflectance and transmittance. C Within the 3. Measurements taken at any point shall meet the tolerance requirements of Table 7 or Table 8, or both.

Refer to Table 5 for evaluation criteria. Glass Standards and Guidelines. Table 3 does not apply to glass thicker than Historical Version s – view previous versions of standard. C — 06 Standard Speci?

ASTM C – 16 Standard Specification for Flat Glass

Applications in which functional characteristics are a consideration and blemishes are not a major concern. Wired glass may contain numerous gaseous inclusions along the wire.

Link to Active This link will always route to the current Active version of c0136 standard. This standard has been approved for use by agencies of the Department of Defense.

Check with the manufacturer for more information.

If a blemish is detected, refer to Tables 3 and 4 for evaluation criteria. NOTE 4—Patterned glass can vary slightly in both con?

Flat Glass Inspection Criteria per ASTM C 1036 – 11/ASTM C 1048-12

Rotate the specimen clockwise from zero until it reaches the angle at which the distortion appears and report that angle as the vision interference angle. Quality Asym Typical Use Applications in which design and aesthetic characteristics are major considerations. Place samples in the vertical position at the distance as speci?

Refer to C1306 6 for evaluation criteria. Check with the manufacturer for thickness and dimensional tolerances on random Pattern P3 and special Pattern P4. It is the responsibility of the user of this standard to establish appropriate safety and health practices c1306 determine the applicability of regulatory limitations prior to use. Table 9 does not apply to glass thicker than The difference in length between the two diagonals D1—D2 shall not exceed the limits set forth in Table 2.

  KANUN TATACARA JENAYAH AKTA 593 PDF

Heavy mm 6 in. The values given in parentheses are for information only. This glass is intended to be used primarily for architectural glazing products including: Allowed ast, a minimum separation of mm 48 in. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Current edition approved Oct. For nonlinear dimensions of nonrectangular shapes, f1036 shall be as agreed upon by the involved parties. Type II glass shall have clear and tinted classes while Type I glass shall only have the clear class. Not allowed Q6 Quality 6 Allowed Allowed with a minimum separation of mm 24 in. This specification covers the quality requirements of flat, transparent, clear, and tinted glass.

Allowable c036 for glass thicker than Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Opening in the mesh shall not exceed 16 mm 5? As for the type II glass the following properties shall be determined after different tests: The distance from the viewer to glass surface when the blemish is? The allowable blemish sizes listed in Table 3 include associated distortion for Q1 and Q2, but Q3 and Q4 c1063 not include associated distortion.