Pinards PDF

UCC, UCC UCC, UCC SLUSC−SEPTEMBER − REVISED DECEMBER TRANSITION MODE PFC CONTROLLER. 1 . UCCP IC PFC CTLR TRANS-MODE 8-DIP Texas Instruments datasheet pdf data sheet FREE from Datasheet (data sheet) search for. Details, datasheet, quote on part number: UCC Part family, UCC PFC Controller for low to medium power applications requiring compliance with.

Author: Tezahn Yozshunris
Country: Madagascar
Language: English (Spanish)
Genre: History
Published (Last): 14 March 2007
Pages: 39
PDF File Size: 16.52 Mb
ePub File Size: 1.88 Mb
ISBN: 980-7-21242-593-7
Downloads: 42566
Price: Free* [*Free Regsitration Required]
Uploader: Tausida

Not recommended for new designs. The supply voltage for the chip. The bias voltage should also be clamped with an external zener diode to a maximum of 18 V.

Maximum Current Sense Threshold? This prevents further rise in output voltage. ESR and the maximum RMS ripple current rating may also be important especially at higher power levels. This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe.

Transition Mode Control The boost converter, the most common topology used for power factor correction, can operate in two datashest — continuous conduction code CCM and discontinuous conduction mode DCM.

Below the UVLO threshold, the output is held low. For medium to higher power applications, where the input filter requirements dominate the size of the magnetics, the CCM boost is a better choice due to lower peak currents which reduces conduction losses and dztasheet ripple current which reduces filter requirements.

Product device recommended for new designs. The information provided on this page represents TI’s knowledge and belief as of the date that it is provided. TI has announced that the device will be discontinued, and a lifetime-buy period dattasheet in effect. Device has been announced but is not in production.

The schematic is shown in Figure 4 and the board layout for the reference design is shown in Figure 5. This pin senses the boost regulator output voltage through a voltage divider. The dynamic range of the inputs can be found in the electrical characteristics table. However, implementations of the control functions are different. Efforts are underway to better integrate information from third parties.

  2007 CAMRY HYBRID OWNERS MANUAL PDF

TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. An internal clamp on the multiplier output terminates the switching cycle if this pin voltage exceeds 1. For wide line variations, a resistor, RB, is necessary in order to permit clamping action.

(PDF) UCC Datasheet PDF Download – UCCx UCCx Transition Mode PFC Controller (Rev. G)

In addition to generating a 2. Additional filtering at switching transient frequencies can be achieved by adding CS1. UCCDR to order quantities of 2, devices per reel.

UCC employs a transconductance amplifier gM amp with gain scheduling for improved transient response refer to Figure Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. The enable comparator ensures that datqsheet controller is off if the feedback sense path is broken or if the input voltage is very low.

An external gate drive resistor may be needed to limit the peak current depending on the VCC voltage being used.

(PDF) UCC28051 Datasheet download

TI’s terms “Lead-Free” or “Pb-Free” mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0. During zero power or overvoltage conditions, this pin goes below 2.

Keep in mind that the low corner frequency 2801 this filter may compromise the overall power factor. Internal active voltage clamps are provided to prevent this pin from going below ground or too high. The chip reference ground. It is a variable frequency control technique that has inherently stable input current control while eliminating reverse recovery rectifier losses.

  JULIE GARWOOD KILLJOY PDF

Highly accurate internal bandgap reference leads to tight regulation of output voltage in normal and OVP conditions, resulting in higher system reliability. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. The gate drive output for an external boost switch.

All bypassing elements are connected to ground pin with shortest loops feasible. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or datasheeh voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.

Inductor Selection In the transition mode control, the inductor value needs to be calculated to start the next switching cycle at zero current.

The voltage acts as one of the inputs to the internal multiplier. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

Enhanced slew-rate of the compensation capacitor results in a faster start-up and transient response. Body dimensions do not include mold flash or protrusion, not to exceed 0.

Texas Instruments

Reproduction of Dataeheet information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.

The bias capacitor must be large enough to maintain sufficient voltage with ac line variations. This pin has a clamp at approximately 5 V.